Comments on: Correcting the Autopano-Sift Hugin Error in 8.10

By: Erik

Erik — Wed, 04 Nov 2009 02:08:41 +0000

I had the same problem, removing the spaces in the name worked like a charm! Furthermore, deleting (in linux that is) the .hugin file can help some of the error 1 problems as well.

By: Tom

Tom — Fri, 07 Aug 2009 01:54:55 +0000

I had an apostrophe in the folder name where photos were stored, i got rid of it and all good.

By: Jackie

Jackie — Thu, 16 Jul 2009 12:51:47 +0000

Thank you Eric! This problem has been bugging me for quite some time, and your suggestion did the trick. Anyone know if this has been reported upstream?

By: Eric

Eric — Wed, 20 May 2009 04:06:46 +0000

I was getting the “failed with error code: 1″ and I figured out that directories with spaces in the name will cause this error. If your directory has a space in it like “My Pictures” replace it with an underscore or something, like “My_Pictures”

By: Juanma

Juanma — Thu, 23 Apr 2009 07:17:18 +0000

Thank you!!!

In my hugin versión it appears “–points %p -o %o %i”. I must change “–” with “-” before “points” and It runs

By: w

Thu, 12 Mar 2009 15:45:09 +0000

it seems autopano-complete doesn’t like mixing long (–points) and short (-o) commandline options. replace –points with -p and everything should work ok (at least that’s what made it work for me)

By: BobD

BobD — Wed, 11 Mar 2009 12:59:24 +0000

@Clemens
Thanks for catching the “- – ” issue, that did fix my problem.

Was able to use autopano-c-complete.sh from S. Nowozin to generate control points.

Bob

Sorry for the late reply

By: gerg

gerg — Sat, 07 Mar 2009 06:51:06 +0000

ha,
i was getting the error:255 and all that. reinstalled. went bleeding edge and installed the .8 beta.
still no go.
i somehow removed autopano and never reinstalled it and that will give you the same error.

By: Inaxio

Inaxio — Thu, 05 Mar 2009 22:00:38 +0000

Thank you!

I had the same problem.

By: Clemens

Clemens — Sun, 01 Mar 2009 12:12:37 +0000

Thanks a lot.
@Remy: Note that before “points”, it has to be “minus minus”. Unfortunately, some text editors and apperently the engine running this homepage, translates minus minus to longminus.

So just go back to the preferences dialoge and change the single long minus into two short minuses without a space between them. Worked for me.

Cheers,
Clemens

By: Rémy

Rémy — Sat, 28 Feb 2009 08:19:05 +0000

I tried the above solution to fix the error. Now it’s another error :

command: “autopano-complete” –points 20 -o ap_resyphXwp “/home/lyr/Bureau/IMG_0001.JPG” … “/home/lyr/Bureau/IMG_0010.JPG”
failed with error code: 1

Any idea ?

By: ciruman

ciruman — Sun, 22 Feb 2009 19:30:36 +0000

Hi,

Did you notice that this page doesn’t allow double minus together? if I writte — (minusminus)as result it returns llongminus, but shoud be – - (minusminus, without spaces). It would be much better if you execute the command on a a terminal and sends the result.

Good luck!

Thank you very much!

By: BobD

BobD — Fri, 20 Feb 2009 12:34:15 +0000

Yes, I enter the post parameters, Here is the error. Please note: the Autopano config line below the Autopano-SIFT are blank.

command: autopano-complete –points 10 -o /tmp/ap_resqwLhlL “/home/robert/photos/pano-test/dscf0755.jpg” “/home/robert/photos/pano-test/dscf0756.jpg” “/home/robert/photos/pano-test/dscf0757.jpg” “/home/robert/photos/pano-test/dscf0758.jpg”
failed with error code: 255

By: B. mathis

B. mathis — Thu, 19 Feb 2009 15:51:39 +0000

Hi BobD,

Did you try entering the above parameters? Entering the following into the autopano-sift text fields should correct the problem:

line 1 type: autopano-complete
line 2 type: -points %p -o %o %i

The error should disappear. If not, perhaps you are receiving a different error. Feel free to post the error message and I’ll see if I can find a solution.

Good Luck!

By: BobD

BobD — Wed, 18 Feb 2009 15:49:04 +0000

After doing some experimenting, I think I know why Autopano will not run on my system. I Refuse to install mono. Apparently Hugin is hard coded to use mono at some point to call autopano. Even after install the C versions of autopano-SIFT and autopano-complete it bombs out at the every end trying to call autopano.

Yes I can run autopano-sift-c from the command line and import the results, but it would be alot nicer to do this from with-in the GUI.

It is disappointing that Hugin has to rely on MS tech.

By: BobD

BobD — Wed, 18 Feb 2009 13:59:45 +0000

Thanks for posting this, I’ve been playing around trying to get this to work, on and off, for months. needless to say, I have no idea now what the default parameters for autopano should be.

Could you or someone please post them?

Thanks
BD

By: John Haynes Nathan Haynes Haynes Schwelm | Cantileverbrakes

John Haynes Nathan Haynes Haynes Schwelm | Cantileverbrakes — Tue, 17 Feb 2009 16:57:08 +0000

[...] Nathan Haines : Ubuntu and Bug Jam at SCaLE7X | TaleTil [...]